Quiz20

Geography notes

Notes · Geography

Volcanic Landforms (Topography)

Short, exam-focused revision notes. Read a section, then test yourself with a quiz.

2 min read5 sections

Volcanic Landforms (Topography)

Overview ⭐⭐

  • Many landforms are made by cooling of magma below the surface, by lava on the surface, and by piling up of fragments, dust and ash with lava as cones.
  • Cones and craters are not permanent: each new eruption changes or modifies them.
  • Explosive eruptions make several kinds of cones; fissure eruptions make lava plateaus and plains by piling thick basalt over wide areas.
Group
From
Landforms
Extrusive
Explosive eruptions
Elevated: volcanic cones. Depressed: craters, calderas
Extrusive
Fissure eruptions
Lava plateaus and domes; lava plains
Intrusive
Magma cooled below the surface
Intrusive lava domes, batholiths, laccoliths, phacoliths, lopoliths, sills, dykes, volcanic plugs and stocks

1. Elevated forms: volcanic cones ⭐⭐⭐

Cone
Made of
Shape and key points
Examples
Cinder (ash) cone
Volcanic dust, ash and pyroclastic fragments (no lava)
Usually low. Starts as a tiny 'ant mount' (a few cm to a few m) and grows as material piles up; can gain 100 m or more in a week. Slopes 30–45°: larger particles near the crater rest at 40–45°, finer ones at the outer edge. Loose and rarely cemented by lava, so permeable to water; on average less susceptible to erosion and can keep their form for hundreds of years if not blown up
Jorullo (Mexico), Izalco (San Salvador), Camiguin (Luzon, Philippines)
Composite cone (strato-cone)
Alternate layers of lava and fragmental (pyroclastic) material; lava acts as cementing material
The highest of all volcanic cones. Resistant to erosion if coated with thick lava; if the outer layer is fragmental, it is badly eroded. Most of the highest, symmetrical, large cones are of this kind
Shasta, Rainier, Hood (USA), Mayon (Philippines), Fuziyama (Japan), Cotopaxi (Ecuador)
Parasite cone (adventive or lateral cone)
Branches of pipes leave the main pipe when the cone is enlarged; lava and material come out of these minor pipes and build small cones on the outer surface of the main cone
Several smaller cones on the major cone; their lava supply comes from the main pipe
Shastina (parasite cone of Mt Shasta, USA)
Basic lava cone (shield cone)
Light, less viscous lava, low in silica (basaltic)
Lava is very fluid, so it spreads over a large area before cooling: a long cone of very low height, shaped like a shield. Also called the Hawaiian type of cone
Hawaii
Acid lava cone
Highly viscous, silica-rich lava
Lava has very low mobility and cools at once, so high cones with steep slopes form. Also called Strombolian type cones
—
Lava dome
Solidified lava piled around the vents
Like shield cones but larger and more extensive. Three kinds: plug dome (lava filling the vents), endogenous dome (silica-rich viscous lava), exogenous dome (silica-poor, very fluid lava)
—
Lava plug and volcanic neck
Lava that plugs volcanic pipes and vents when a volcano becomes extinct
When the cone erodes away, vertical columns of hard lava stand out. The lava-filled pipe = volcanic neck: cylindrical, 50–60 m high above the ground, 300–600 m across. A neck or pipe filled with breccia = diatreme
Shiprock (New Mexico, USA): 515 m (1,700 ft) above the flat sedimentary rocks around it; a diatreme exposed by erosion
  • Easy contrast: cinder cone = loose fragments; composite cone = lava + fragments; shield cone = lava only, low; acid lava cone = steep and high.

2. Depressed forms ⭐⭐⭐

Craters

  • A crater (volcanic mouth) is the funnel-shaped hollow at the mouth of a vent. Its slope depends on the cone; in a cinder cone it is about 25–30°. It grows as the cone grows.
  • An average crater is about 300 m wide and 300 m deep. Range: small craterlets a few hundred metres across to large craters a few kilometres across.
  • Aniakchak (extinct volcano, Alaska): crater 9.6 km (6 miles) across, walls 364–912 m high.
  • Crater Lake (Oregon, USA): if accepted as a crater it is one of the largest; many scientists call it a caldera. A crater filled with water = crater lake.
  • Nested craters (craters within the crater, grouped craters): when a very large crater has later smaller eruptions, small cones and craters form inside it. Formed only when the next eruption is weaker than the previous one. Mt Taal (Philippines) has 3 inside its large crater; Vesuvius 3; Etna 2.
  • Adventive crater: crater at the mouth of a parasite cone on a large volcanic cone.

Calderas ⭐⭐⭐

A caldera is generally an enlarged crater, bounded by steep walls on all sides. Two parallel ideas explain how it forms:
ㅤ
Subsidence concept
Eruption (explosion) concept
Idea
The caldera is an enlarged crater formed by subsidence (sinking)
Calderas form from violent, explosive eruptions of the volcano
Who
First group of scientists; put forward by the U.S. Geological Survey
Second group; Daly is the leading advocate
Examples
Aso (Japan) and Crater Lake (USA) are results of subsidence
—
Argument
—
Daly calls forms made by subsidence 'volcanic sinks'. If calderas were made by subsidence there should be no pyroclastic deposits related to the volcano near them, but volcanic material is found several km away, e.g. 128 km from the Crater Lake caldera
Significant calderas (size in km)
Place
Lake Toba (50 × 50)
Sumatra
Aira (25 × 24)
Japan
Lake Kutchaio (26 × 20)
Japan
Tarso Yega (20 × 17)
Sahara (Africa)
Aso San (23 × 14)
Japan
Alban (11 × 10)
Italy
Crater Lake (10 × 10)
USA
Krakatoa (7 × 6)
Indonesia
Kilauea (5 × 3)
Hawaii
  • Smaller calderas inside a big caldera = nested (grouped) calderas.
  • Difference from a crater: a caldera is much larger and differs in size and mode of formation.

3. Lava plateaus and plains ⭐⭐

  • Made by fissure flows: thick layers of basaltic lava spread over wide areas.
  • Examples (see World Distribution): Columbia plateau (USA), Deccan (India), Parana (Brazil and Paraguay).

4. Intrusive topography ⭐⭐

  • If gases and vapour are not very strong, the rising magma does not erupt but is intruded into voids below the surface and cools into batholiths, laccoliths, phacoliths, lopoliths, sills and dykes.
  • These show on the surface only when the overlying country rocks are removed by long erosion.