Crustal fracture ⭐
- Crustal fracture = breaking and displacement of rocks along a plane, caused by tensional or compressional forces.
- Moderate tension gives only cracks; intense tension displaces rocks and forms faults.
Joint | Fault |
A fracture with no noticeable movement of rocks | A fracture with noticeable displacement of rocks on either side, parallel to it |
Fault ⭐⭐
- A fault is a fracture along which rock blocks have been displaced. The surface of movement is the fault plane.
- Vertical displacement can reach hundreds of metres and horizontal displacement several kilometres, but only a few metres at a time.
- Faults are weak zones where crustal movement continues for a long time.
Parts of a fault ⭐⭐⭐
Term | Meaning |
Fault plane | The plane along which blocks move; can be vertical, inclined, horizontal or curved |
Fault dip | Angle between the fault plane and the horizontal |
Upthrown side | The block that is relatively higher |
Downthrown side | The block that is relatively lower |
Hanging wall | The block above an inclined fault plane |
Footwall | The block below an inclined fault plane |
Fault scarp | The steep, cliff-like slope formed by faulting. Scarps can also form by erosion; only those formed by faulting are fault scarps |
Throw | Vertical displacement between the two sides |
Types of faults ⭐⭐⭐
- By direction of movement: dip-slip (movement along the dip) and strike-slip (movement along the strike).
Type | Movement | Force | Fault plane | Effect |
Normal fault (dip-slip) | Hanging wall moves down the dip; blocks move apart | Tension | Steep: 45° to vertical | Crust extends; forms fault scarps |
Reverse (thrust) fault (dip-slip) | Hanging wall moves up the dip; blocks move towards each other | Compression (horizontal stress maximum) | Gentle: 0° to about 40° | Crust shortens; also called a compressional fault |
Overthrust fault | One block rides over the other | Very strong compression | Almost horizontal | Old rocks over young |
Strike-slip fault | Blocks move horizontally past each other | Horizontal shear | Usually vertical | Little or no scarp. Also called wrench, tear or transcurrent fault |
Oblique-slip fault | Combination of dip-slip and strike-slip | — | — | — |
Step faults | A series of parallel faults, all dipping the same way, with blocks dropping in the same direction | Tension | — | Step-like landscape |
- Strike-slip faults: right-lateral (dextral) if the far block moves to the right; left-lateral (sinistral) if it moves to the left. ⭐
Rift valley (graben) and horst ⭐⭐⭐
- Rift valley = a long, narrow, deep trough bounded by two or more parallel normal faults.
- Graben (German: trough) is used as a synonym. Some say a graben is smaller than a rift valley, but most treat the two as the same.
- Horst = an upstanding block between two faults: a block mountain.
- A rift valley forms in two ways:
- The middle block sinks between two normal faults while the side blocks stay put.
- The middle block stays put while the side blocks rise.
- Press and Siever: tensional forces literally pull the crust apart, dropping fault blocks down.
Examples ⭐⭐
Example | Notes |
Rhine rift valley (Germany) | About 300 km long, between Basel and Bingen; bounded by the Vosges and Hardt (horsts) on one side and the Black Forest and Odenwald (horsts) on the other. The best-defined rift valley |
Great Rift Valley | The longest: from the Jordan valley through the Red Sea to the Zambezi in East Africa |
Dead Sea | Classic rift valley; its shore is about 430 m below sea level, the lowest land on earth |
Death Valley (California) | A graben with its floor below sea level (about 86 m) |
Narmada, Tapi, Damodar, parts of Son (India) | Often cited as rift valleys (debated) |
Central Plain of Scotland; Spencer Gulf (South Australia) | Other examples |
Ocean deeps and trenches | The deepest grabens, e.g. the Bartlett (Cayman) Trough south of Cuba and the Java Trench |
Origin of rift valleys ⭐⭐
No single theory is fully accepted. Views fall into two groups.
1. Tensional hypothesis ("keystone" idea)
- Like the keystone of an arch that drops when the arch cracks: tension opens two parallel cracks, side blocks are pulled apart, and the middle block drops.
- Criticisms:
- Under an arch there is open space; under the crust there is none. The sinking block would have to push aside magma.
- If so, rift valleys should always have volcanic activity, but many do not.
- Tension should let lava pour out, not stop it; yet volcanoes are observed to stop when rifts form.
2. Compressional hypothesis
- Supported by Wayland (Lake Albert, Ruwenzori), Bailey Willis (Dead Sea), Warren D. Smith and E.C. Bullard.
- Compression at depth pushes the side blocks up along thrust faults as horsts (overthrusting rift blocks). The middle block (rift block, narrow at the top and wider below) is forced down between them.
3. E.C. Bullard (1933–34), from gravity surveys ⭐
- A rift block cannot sink by gravity like a keystone; rift valleys form by compression from both sides, in stages:
- Compression buckles a rigid plateau until a crack forms.
- One side overrides the other (thrusting); the other is pushed down.
- A second crack forms in the downthrust block, which is overridden too. The part trapped between the two upthrust blocks becomes the rift valley.
- Width depends on rock elasticity, valley depth and substratum density. With substratum density 3.3: a 20 km deep rift is about 40 km wide; a 40 km deep rift is about 65 km wide.