Quiz20

Geography notes

Notes · Geography

Density, Pressure and Temperature (Artificial Sources)

Short, exam-focused revision notes. Read a section, then test yourself with a quiz.

3 min read3 sections

Density, Pressure and Temperature (Artificial Sources)

Density ⭐⭐

  • Outer layer of sedimentary rocks: about 0.8–1.6 km (½ to 1 mile) thick.
  • Below it, crystalline rocks with density 3.0–3.5.
  • Average density of the earth ≈ 5.5, so the core must be much denser: about 11.
  • So the core is the densest part of the earth.
Who / how
Average density of the earth
Cavendish (1798), using Newton's law of gravitation
5.48
Poynting (1878)
5.49 g/cm³
Satellite studies (since 1950)
Whole earth 5.517 g/cm³; surface rocks 2.6–3.3; core ~11

Pressure: why is the core so dense? ⭐⭐

The reasoning goes in four steps:
  1. Pressure increases density, and pressure rises with depth. So the core might be dense because of the weight of overlying rocks (superincumbent load).
  1. But every rock has a critical limit beyond which pressure cannot increase its density further.
  1. So the core's high density is not due to pressure alone.
  1. Therefore the core must be made of intrinsically heavy metals: a mixture of iron and nickel. This is supported by the earth's magnetic field.

Temperature ⭐⭐

  • From mines and boreholes, temperature rises by about 2–3°C per 100 m (about 1°C per 32 m). It is hard to measure below 8 km.
  • Tectonically active areas (e.g. Basin and Range Province, USA): 1000°C at 43 km, close to the melting point of basalt and peridotite.
  • Stable areas: only 500°C at 40 km.
  • Oceanic plate (slab): about 0°C at the top and 1200°C at the base, where it meets the asthenosphere.
  • If temperature kept rising at the surface rate, it would be about 25,000°C at 2900 km and most of the earth would be molten. It is not.
  • Reason: radioactive minerals are concentrated in the upper crust, so the rate of temperature rise decreases with depth. ⭐

Temperatures at different depths ⭐⭐⭐

Depth
Temperature
Note
100 km
~1100°C
Asthenosphere, partly molten; near melting point
400 km
~1500°C
ㅤ
700 km
~1900°C
ㅤ
2900 km
~3700°C
Mantle–outer core boundary
5150 km
~4300°C
Outer core–inner core boundary

Origin of the earth's internal heat

  • Two sources: decay of radioactive minerals and gravitational energy turned into heat.
  • About 4.7 billion years ago, accretion and adiabatic compression gave an initial temperature of about 1000°C; radioactive heat then raised it.
  • About 4.0–4.5 billion years ago, temperature reached the melting point of iron. Molten iron sank to the centre ("iron catastrophe"), releasing about 2 × 10³⁷ erg of heat.
  • This large-scale melting and sorting formed the crust, mantle and core. ⭐

Transfer of heat

  • Heat flows from the interior outward.
  • Conduction is very slow, because rocks are poor conductors: heat crosses a 10 m rock layer in about 3 years; a 100 m lava flow takes about 300 years to cool; heat would take about 5 billion years to cross a 400 km layer.
  • Radiation is ineffective because interior minerals are opaque.
  • Convection is the likely mechanism, although it works best in liquids.

Internal vs external heat ⭐

  • The sun's heat drives atmospheric and hydrological processes and denudation (destructive).
  • The internal heat builds mountains, plateaus, faults, volcanoes and earthquakes (constructive).
  • Press and Siever (1974): "The earth's internal heat engine builds mountains and its external heat engine, the sun, destroys them."