Quiz20

Geography notes

Notes · Geography

3. Topographical Maps, Contours & Relief

Short, exam-focused revision notes. Read a section, then test yourself with a quiz.

5 min read8 sections

3. Topographical Maps, Contours & Relief

🎯
Key points: meaning of topographical maps; Survey of India numbering and scales (million, degree, 1:50,000 and 1:25,000 sheets); Open Series Maps; conventional signs and colours; methods of showing relief (hachures, hill shading, layer tints, spot heights, bench marks, contours); contour interval, horizontal equivalent, gradient; contour patterns of landforms and slopes; profiles and intervisibility; morphometric curves; interpretation of topographical maps.

1. Topographical Maps

  • Topographical (topo) maps are large-scale general maps showing natural and cultural features – relief, drainage, vegetation, settlements, roads, railways, boundaries – prepared from precise surveys. In India they are made by the Survey of India (Dehradun).
  • Used for military, planning, engineering, field studies, settlement and land-use analysis; the spatial pattern of rural settlements is best studied on toposheets.

Classification of Indian toposheets (old Survey of India / Defence series) ⭐⭐⭐

Series
Extent
Scale
Numbering example
Million sheet (India and adjacent countries)
4° × 4°
1:1,000,000
Numbers 39 to 92 – e.g., 53, 63
Degree sheet (quarter-inch sheet)
1° × 1° (16 per million sheet)
1:250,000
Letters A to P – e.g., 63K, 55J
1:100,000 sheet (half-inch, old)
30′ × 30′
1:126,720 old / 1:100,000
NE, NW, SE, SW quadrants – "quadrant sheets"
1:50,000 sheet (inch sheet)
15′ × 15′ (16 per degree sheet)
1:50,000 (old 1 inch to 1 mile = 1:63,360)
Numbers 1 to 16 – e.g., 63K/12, 47D/11
1:25,000 sheet
7½′ × 7½′ (4 per 1:50,000 sheet)
1:25,000
63K/12/NE or 63K/7/2
  • Numbering from north to south (columns) and from west to east; degree sheets lettered column-wise from the north-west.
  • Scale order (larger to smaller): 63K/7/2 (1:25,000) > 47D/11 (1:50,000) > 55J (1:250,000) > 63 (1:1 million).
  • Contour intervals commonly: 1:25,000 – 10 m; 1:50,000 – 20 m; 1:250,000 – 100 m (40 m in some sheets) 🔴 (varies with relief).
  • International Map of the World (IMW) – 1:1,000,000, 4° latitude × 6° longitude sheets, modified polyconic projection.
  • National Map Policy 2005: two series – Defence Series Maps (DSM) (restricted) and Open Series Maps (OSM) (public) on the WGS-84 datum, UTM projection with a new sheet numbering. Topographic data and OSM toposheets are now freely downloadable after the National Geospatial Policy 2022. Earlier sheets used the Everest spheroid and polyconic projection.
  • Datum = reference surface for heights (mean sea level, fixed from long tide-gauge records). The datum is hard to fix because sea level fluctuates in time and place.

Conventional colours on Survey of India toposheets ⭐⭐

Colour
Feature
Black
Names, railways, telegraph lines, boundaries, dry stream beds, surveyed trees, broken ground
Blue
Water features – rivers, lakes, wells, tanks, canals, coast
Brown
Contours, form lines, sand dunes, rocky ground
Green
Forests, trees, grass, scrub, orchards
Yellow
Cultivated land
Red
Settlements, built-up areas, roads, grid lines (eastings, northings)
White
Uncultivated / unsurveyed land
  • Land-use map colours: cultivated – yellow; forest – dark green; water – blue; built-up – red; barren/uncultivable – brown; plateau tint light brown.
  • Grid references: eastings (read first, "along the corridor") then northings ("up the stairs") – 4-figure and 6-figure references.
  • Marginal information: sheet number, scale, contour interval, magnetic variation, index to adjoining sheets, legend, year of survey.

2. Methods of Showing Relief ⭐⭐⭐

Method
Description
Merit / limitation
Hachures
Short, fine lines drawn in the direction of slope (down the slope); thicker and closer for steeper slopes (Lehmann's system, 1799)
Good visual picture; no exact height, crowds the map
Hill shading
Slopes shaded assuming light from the north-west (oblique) or from above (vertical)
Gives 3-D effect; no heights
Layer tints (colour layering)
Height zones in different colours – green (lowlands) → yellow → brown → white (snow); blue shades for sea depth
Used in atlases and wall maps
Spot height
Dot with height of a point (determined by survey)
Exact height of a point only
Bench mark (BM)
Height marked on a permanent object (building, pillar)
Exact, used by surveyors
Triangulation station (△)
Point of triangulation survey, height given
Exact
Form lines
Approximate contours drawn as broken lines without exact survey
Approximate
Contours
Lines joining places of equal height above mean sea level
Most accurate and widely used; need skill to read
Relief models, block diagrams, DEMs
3-D representations
Modern
  • Depth contours in water = isobaths.

3. Contours – Terms and Calculations ⭐⭐⭐

Term
Meaning
Contour interval (CI) / vertical interval (VI)
Constant difference in height between two successive contours
Horizontal equivalent (HE)
Horizontal (map-scaled ground) distance between two successive contours
Gradient
VI ÷ HE (both in the same units) – expressed as ratio (1:50), fraction, tan θ or degrees
Index contour
Every 5th contour drawn thicker and labelled
Vertical exaggeration (VE)
Ratio of vertical scale to horizontal scale in a profile = HS denominator ÷ VS denominator
  • Gradient example: 1:50,000 map, A on 200 m and B on 240 m contour, map distance 4 cm → VI = 40 m; HE = 4 × 50,000 = 2,000 m → gradient = 40/2000 = 1 in 50.
  • Points 250 m and 500 m apart vertically with HE 1,000 m → tan θ = 250/1000 = 0.25.
  • Rules of contours: contours never cross (except an overhanging cliff) and never branch; close spacing = steep slope, wide = gentle; equal spacing = uniform slope; contours of the same height cannot merge except at a vertical cliff; every contour closes on itself (on or beyond the map); contours bend upstream in valleys.

Contour patterns of landforms

Contour patterns: conical hill, plateau, V-shaped valley, spur, cliff and saddle.
Contour patterns: conical hill, plateau, V-shaped valley, spur, cliff and saddle.
Landform
Contour pattern
Conical hill
Concentric, roughly circular, evenly spaced, value increasing inward
Plateau
Outer contours close together (steep sides); flat top with widely spaced or no contours
Ridge
Elongated closed contours
Saddle / col
Low point between two hills; contours of two summits enclosed by a common contour ("hour-glass"); a deep col is a pass
V-shaped valley
V-shaped contours pointing upstream / towards higher ground
U-shaped (glacial) valley
U-shaped contours with wide flat floor, steep sides
Gorge / canyon
Very close contours on both sides of a narrow valley
Spur
V-shaped contours pointing downslope / towards lower ground
Cliff / escarpment
Contours run very close and merge
Waterfall
Contours converge across a river channel
Crater / volcano
Concentric contours with lower values inside the innermost (depression) – depression contours marked with ticks
Interlocking spurs
Alternating spurs on both sides of a winding valley

Contour patterns of slopes

Uniform, concave and convex slopes (the top line is the highest).
Uniform, concave and convex slopes (the top line is the highest).
Slope
Pattern
Uniform / even
Equally spaced contours
Concave
Contours close at higher levels, wide apart at lower levels (steep top, gentle base)
Convex
Contours wide apart at higher levels, close at lower levels (gentle top, steep base)
Terraced / stepped
Alternate close and wide spacing
💡
Valley V → Up (points uphill); Spur V → Down (points downhill). Concave = Close at the top (C-C).

4. Profiles and Intervisibility

  • Profile (section) = side view of the ground along a line, drawn from contours: mark contour crossings on a paper strip, plot heights on a vertical scale (with vertical exaggeration).
  • Longitudinal profile – along a river or road; cross profile – across a valley.
  • Types of multiple profiles: serial (parallel profiles side by side), superimposed (several on one base), projected (only the parts visible from a direction – skyline view), composite (highest points only – shows erosion surfaces).
  • Intervisibility: whether two points can see each other – determined by drawing a profile and a line of sight; concave slopes allow intervisibility, convex slopes block it. In GIS: viewshed analysis.

5. Morphometric and Relief Analysis (frequently asked)

Technique
What it shows
Hypsometric (area–altitude) curve
Proportion of area above/below each height (percentage hypsometric curve – Strahler, 1952 – stage of erosion of basin)
Hypsographic curve
Percentage of the whole earth's land and sea-floor area at each height/depth
Altimetric frequency curve / graph
Frequency of spot heights and summits at each height – identifies erosion surfaces
Clinographic curve
Average gradient between successive contours – highlights abrupt slope changes
Relative relief map
Difference between highest and lowest points per grid square (Smith, 1935)
Average slope map
Wentworth (1930) method: slope = (number of contour crossings × CI) ÷ (0.6366 × grid line length)
Trachographic map
Shows average slope and relative relief together
Dissection index, drainage density, stream ordering (Strahler, Horton)
Basin morphometry; Horton's form factor = A/L²

6. Interpreting a Topographical Map

  1. Marginal information – sheet number, scale, CI, location (latitudes/longitudes), state/district.
  1. Relief and slope – highest and lowest points, landforms, direction of slope.
  1. Drainage – rivers, direction of flow, pattern (dendritic, trellis, radial, parallel), perennial or seasonal, tanks.
  1. Natural vegetation – forests (reserved/protected), scrub.
  1. Land use – cultivated land, irrigation (canals, wells, tanks).
  1. Settlements – types (compact, dispersed, linear), sites (along rivers, roads), patterns; towns and functions.
  1. Transport and communication – roads, railways, footpaths, post offices.
  1. Correlation – relate relief, drainage, vegetation, settlement and occupation (e.g., settlements along roads on plains, dispersed in hills).

⚡ Quick Revision

  • Million sheet 4°×4° (39–92); degree 1°×1° (A–P, 1:250,000); 15′×15′ (1:50,000, 1–16); 7½′ (1:25,000).
  • Yellow = cultivated; red = settlements; brown = contours; blue = water; green = forest; black = names, railways.
  • Hachures follow slope; hill shading light from NW; contours most accurate.
  • Gradient = VI/HE. Valley V points upstream; spur V points downhill. Concave = close at top; convex = close at base.
  • Hypsometric = area–altitude; altimetric = spot heights; clinographic = average gradients; trachographic = slope + relative relief.

📝 Practice MCQs

  1. A 1:50,000 toposheet covers: (a) 1° × 1° (b) 30′ × 30′ (c) 15′ × 15′ (d) 7½′ × 7½′
Answer
(c) 15′ × 15′
  1. Contours are shown on Survey of India toposheets in: (a) black (b) blue (c) brown (d) green
Answer
(c) Brown
  1. Contours close at the top and wide apart at the base show a: (a) convex slope (b) concave slope (c) uniform slope (d) terraced slope
Answer
(b) Concave slope
  1. Short lines drawn in the direction of the slope are: (a) form lines (b) hachures (c) contours (d) isobaths
Answer
(b) Hachures
  1. On a 1:25,000 map two contours (100 m and 150 m) are 2 cm apart. Gradient? (a) 1:10 (b) 1:20 (c) 1:50 (d) 1:100
Answer
(a) 1:10 – HE = 2 × 25,000 cm = 500 m; 50/500
  1. Which curve uses the frequency of spot heights? (a) Hypsometric (b) Clinographic (c) Altimetric frequency (d) Lorenz
Answer
(c) Altimetric frequency curve